audiofrog
amplifiers
HiFi Class-D
Sometimes great products are the result of a new invention—a new technological advancement that unlocks performance, features or applications never before possible. We have people like Henry Ford and the Wright Brothers to thank for those kinds of advancements.
More often, great products are the result of painstaking attention to detail and optimization of existing technology—someone got a whole bunch of stuff right—and the results are amazing.
Audiofrog HiFi Class-D amplifiers are an example of the latter—Class-D done right.
A150.4D High Fidelity Class-D Amplifier
Class-D amplifiers haven’t always been great. Early versions, which debuted nearly 30 years ago were fraught with problems: noise, instability, distortion were three significant shortcomings. The promise of class-D—smaller chassis and higher efficiency were always at the forefront but audio performance never quite approached that of Class-A or even Class-AB. Now, there are class-D amplifiers that rival the best performers in any class.
Thanks to a host of features and that painstaking attention to detail and optimization, Audiofrog HiFi Class-D amplifiers provide the high power, low noise and low distortion performance audio enthusiasts expect in small and rugged chassis that are easy to install and can be made to fit nearly anywhere.
Four Layer PCB (Printed Circuit Board)
Board layout is a key component of a high fidelity amplifier design, especially when miniaturization is a key feature. Audiofrog HiFi Class-D amplifiers incorporate a four layer PC board that helps to isolate the magnetic circuit in the power supply and Class-D modulators from the amplifier’s preamp and audio sections. Small I/E transformers oriented to place the preamp circuit in a magnetic null replace the toroidal transformers often used in larger designs. High speed switches responsible for power supply and output voltage are located on the opposite side of the board from the preamp and audio circuits and are isolated by an internal shield layer. Heat is transferred from the switches on the bottom of the board to the heat sink on the top through heat sink pads incorporated into the top and bottom PC board layers.
Audiofrog HiFi Class-D amplifiers provide noise free performance unmatched by similarly sized high power class-D amplifiers.
Ultra High-Frequency Switching
Ultra High-Frequency Switching in our new HiFi Class D-designs move the power supply switching frequency to 100kHz and the class-D modulator frequency to 420kHz. This allows for dramatically smaller magnetics and smaller transformers make a smaller amplifier possible. In addition, the higher modulation frequency makes it possible to move the output low pass filter frequency an octave higher than many other class-D designs. The output filter in Audiofrog’s new HiFi Class-D designs is set to 40kHz rather than the usual 20kHz.
Because the output filter in a class-D amplifier is a passive low pass filter, it has to be designed for a specific load—usually 4 ohms. When measured with other loads, the frequency response changes at and around the filter frequency. A higher resistance load creates a peak at the filter frequency and a lower resistance load causes attenuation at and around the filter frequency. This has long been a criticism of class-D design.
In the example below, the performance at 4 Ohms is within about 3dB of flat response. At 8 Ohms, the underdamped filter causes almost a 3dB peak at 20kHz, which can amplify audible high frequency noise present in the system. At 2 Ohms, 20kHz is attenuated by nearly 8 dB.
The 40kHz filter frequency in Audiofrog’s HiFi Class-D amplifiers moves most of the frequency response changes with varying terminal loads to a frequency higher than we can hear. At 20kHz, the response is within the typical +/-3dB, common for frequency response measurements. This is better.
This common measurement of amplifier frequency response is useful for comparing one amplifier to another, but amplifiers drive speakers, not resistors.
Speakers aren’t resistors. Speakers are reactive loads and when discussing speakers as amplifier loads, we use the term “impedance”. The impedance of a speaker is not a simple number like a resistor. At and around the speaker’s resonance, the speaker is also a generator of electricity and that generation creates a peak in the impedance. Because the wire in the speaker’s voice coil is wound around a tubular former, the speaker’s voice coil has inductance, which resists a change in the flow of current and the impedance increases at high frequencies.
Below is the impedance graph of a typical tweeter showing the peak at resonance and the increase in impedance at high frequencies.
Audiofrog tweeters are a little different. All Audiofrog tweeters include a shorting ring in the form of a copper cap over the polepiece. This shorting ring helps to minimize the voice coil’s inductance by acting as a shorted secondary winding in a transformer made up of the voice coil and the shorting ring. The result is much more linear impedance at high frequencies when compared to tweeters that don’t include this feature.
This linearization of the high frequency impedance in Audiofrog tweeters gives us an opportunity for an additional performance enhancement in Audiofrog amplifiers when they’re used with Audiofrog tweeters. We have optimized the amplifier’s output filter to provide almost ruler-flat response when used with Audiofrog GB15, GB10, GS10 or G60S.
When used with Audiofrog tweeters, the frequency response of the A150.4D is 20Hz-20kHz, +/- 0.1dB! Using the half-power point as the frequency response limit (+/-3dB,) the frequency response is extended to 45kHz.
Audiofrog HiFi Class-D amplifiers, used in conjunction with Audiofrog tweeters provide near ruler flat amplifier frequency response up to the high frequency limits of our hearing.
Flex Crossover
The onboard crossover in the Audiofrog A150.4D can be selected per pair of channels as a high pass, a bandpass or defeated completely when the amplifier will be used with a separate signal processor. In addition, each filter includes a X10 frequency range switch so the amplifier can be configured with crossover points suitable for nearly any system configuration.
The A600.1D mono amplifier is designed to drive subwoofers and includes a high pass filter, with a frequency range from 5Hz to 40Hz, suitable for use as a subsonic filter for vented enclosures or for use with small subwoofers. The low pass filter is adjustable between 50Hz and 500Hz making it appropriate for subwoofers or for midbass drivers. When used with an outboard processor or DSP, the filters can be selected at 5Hz and 500Hz to keep the onboard crossovers well outside the range of DSP settings you’ll use for the subwoofer .
In addition, the A600.1D includes a phase adjustment control to make getting the phase right between the subwoofer and the midbass drivers easier, even in systems without a DSP.
Audiofrog HiFI Class-D amplifiers include on board crossovers flexible enough to support most any system configuration and can be defeated when the amplifiers will be used with a digital signal processor.
Integrated Feedback
Based on IR’s 2092 integrated class-D audio driver, feedback through an operational trans-conductance amplifier provides an analog version of a sigma-delta convertor, which shifts error in the audible frequency range upwards to the inaudible high-frequency spectrum, dramatically reducing noise in the signal. Dead time is programmable for optimization of zero-crossing with minimum distortion.
Audiofrog HiFi Class-D amplifiers provide noise and distortion performance that rivals the best class AB amplifiers in significantly smaller and more efficient packages.
HSS Heat Sink Shield
Audiofrog HiFi Class D amplifiers include a dual purpose heat sink that also acts as an EMI shield. The heat sink and the bottom plate are electrically connected to each other and to one of the internal PCB layers through a trace that runs the perimeter of the board on the top and on the bottom. Combining the sink, the bottom panel and a PCB layer help to minimize EMI (electromagnetic interference) emitted from the amplifier, which prevents degradation of the radio’s FM reception.
Compared to many other class-D amplifiers, Audiofrog HiFi Class-D amplifiers emit less noise, which preserves FM reception and minimizes radiated noise which may be picked up by other audio components.
Differential Inputs
As the name implies, differential signal inputs are designed to amplify the difference between the positive and negative signal conductors. Differential inputs are suitable for use with both balanced outputs, in which one conductor carries the signal and the other conductor carries the inverse of the signal, or with single-ended outputs, in which one conductor carries the signal and the other conductor is connected to audio ground.
In cars, audio ground is often the same as power supply ground, which is chassis ground. Chassis ground is also ground for every switch and motor in the car and also for the alternator. Many previous amplifier input topologies used single-ended inputs, which were notorious for creating ground loops and for susceptibility to radiated noise. It doesn’t matter how quiet the amplifier circuit is if the input is noisy.
Differential inputs solve these problems in two ways. First, neither conductor is connected directly to chassis ground, so the potential for ground loops is nearly eliminated. Second, because signals that appear identically on both conductors are cancelled through CMNR (common mode noise rejection), radiated noise, picked up by the cables, can be eliminated in the input preamp. In order for this to work, it’s important to use twisted pair cable rather than shielded coaxial cable.
Because the connection to ground is eliminated in the input section, differential inputs are suitable for connection to both the single ended line level output of head units and signal processors and for connection to the balanced, speaker level output of head units and factory installed amplifiers. RCA jacks are provided for standard preamp connections and a convenient Molex-style connection plug is provided for connection to speaker level outputs.
Audiofrog HiFi Class-D amplifiers include differential inputs suitable for connection to line level sources up to 10V or speaker level sources up to 30V. Speaker level and line level inputs also include signal sensing turn on for applications in which no remote turn on lead is supplied by the vehicle’s head unit.
Remote Level Control Sync
The A600.1D amplifier is compatible with the AF-RLC remote level control. The RLC is connected to the amplifier using an attached RJ-15 phone cord. When attached, the RLC will allow the user to vary the level of the subwoofer amplifier between the level setting on the control panel and infinite attenuation.
One RLC can control more than one A600.1D amplifier and through a unique feature called RLC-Sync, the level of all of the connected amplifiers will be synchronized (within about 1dB) with the amplifier that has the lowest control panel level setting.
If you’d prefer to make a custom RLC with a cool knob of your choice, plans are included in the owner’s manual for installing and connecting your own design.